Top Load Washers
Maytag Top Load Washer Diagnostic Codes for
Model(s)
MAT12PDB – MAT12PDD – MAT12PRB – MAT12PRD – MAT12PDL – MAT12PSL – MAT14PD – MAT14PR
d1 Water level circuit failure on control board
d3 Water temperature sensor error (When equipped with temperature sensing water valve)
d4 Lid switch circuit failure on control board
d5 Blocked Coin 1 or Coin 1 circuit error
d7 Slow fill detected
d8 Slow drain detected
d9 Low voltage detected
d12 Motor sense circuit failure on Control Board
d13 Blocked Coin 2 or Coin 2 circuit error
d16 Control board not receiving communication from debit card reader
MVW18PD – MVW18PR – MAT20PD – MAT20PR
F01 Main control fault
F03 Pressure sensor fault
d5 Blocked Coin 1 or Coin 1 circuit error
F07 Shifter/Actuator fault
d9 Low voltage detected
F11 Motor control fault
d13 Blocked Coin 2 or Coin 2 circuit error
d16 Gen 2 debit card communication error
F20 Long fill detected
F21 Long drain detected
F22 Lid lock fault
F24 Temp sensor fault
F25 Basket speed sensor fault
F26 Lid switch fault
F27 Overflow detected
F29 Lid unlock fault
F32 No fill fault
F70 CCU to UI Communication fault
F71 CCU to UI Communication fault
F73 UI EEPROM fault/error
F74 UI EEPROM fault/error
F77 Off balance load detected
Front Load Washer
Model(s) Code Description
MAH14 – MAH20 – MAH21
d4 Door sense error on control board
d5 Blocked Coin 1 or Coin 1 circuit error
d7 Slow fill detected
d8 Slow drain detected
d9 Low voltage detected
d10 Door lock sense error
d11 Motor speed error detected
d13 Blocked Coin 2 or Coin 2 circuit error
d16 Gen 2 debit card communication error
MAH22 – MHN30 – MHN33
F01 CCU Error
F03 Accelerometer failure **MHN33 Only**
F04 Accelerometer failure **MHN33 Only**
d5 Blocked Coin 1 or Coin 1 circuit error
d9 Low voltage detected
F11 Motor Control Unit failure
d13 Blocked Coin 2 or Coin 2 circuit error
d16 Gen 2 debit card communication error
F20 Slow fill error
F21 Slow drain detected
F22 Door lock error
F24 Temperature sensor error
F25 Tachometer error
F26 Door switch error
F27 Overflow condition detected
F28 Communication error between CCU and MCU
F29 Door unlock error
F30 Dispenser system error – **MAH22 Only**
F31 Motor overheating
F33 Pump sensed disconnected
F34 Load detected during Clean Cycle
Maytag Commercial Laundry Help Codes
MAH22 – MHN30 – MHN33
0F
Oversuds detected during cycle, and washer was not able to
resolve an unbalance condition detected during final spin.
32
More than 6 unbalance retries during the final spin – spin
(and cycle) has been aborted.
33
Oversuds detected during wash cycle and washer was not
able to resolve the condition – cycle has been aborted.
71
Generation 2 debit card cycle polling message out of
sequence.
74
Generation 2 debit card remaining balance message out of
sequence.
75
Generation 2 debit card new card balance message out of
sequence.
88
Invalid messaging state found in data acquisition
communications
MAH14 – MHN20 – MAH21
8 Motor sensed not turning during wash cycle
F
Suds lock possible or machine overload with clothing,
spinning at less than 500rpm
10 Moto sensed not turning during spin cycle
17 Door was not locked at end of the final spin
19
Water level was reached during the wash cycle, but water
level was not maintained during cycle.
1b
Slow fill, water level never reached resulting in water valve
being turned off during pause in cycle
1d
Unbalance within a speed at greater than 500rpm and less
than 675rpm during final spin cycle
2A
Motor on full power for 15 seconds during the final spin at
500rpm and less than 675rpm. Machine will spin at slower
speed.
2F Motor speed error during spin
30 Motor speed error during wash cycle
31
Spin cycle was delayed due to wash level being sensed for
more than 60 seconds at the start of the spin
32
Unbalance at less than 500 rpm during final spin. Spin cycle
was stopped.
33 Suds detected during wash cycle
34 Spinning below 85 rpm too long during spin cycle
35 Tumbling above 50 rpm too long during wash cycle
36
Motor not slowing down after 120 seconds of coasting down
after reaching 300 rpm
37 Motor running too fast during tumble cycle
39
Motor still running after 120 seconds of coasting down after
and unbalance
40 Motor running faster than 85 rpm and the door is not locked
71
Generation 2 debit card cycle polling message out of
sequence
74
Generation 2 debit card remaining balance message out of
sequence
75
Generation 2 debit card new card balance message out of
sequence